Arduino UNO +Prototype Shield(with Breadboard Jump Wires) + L293D Motor Drive Shield For Arduino Duemilanove Mega UNO R3 AVR ATMEL
$29.96
Details L293D Motor Drive Shield Kit For Arduino Duemilanove Mega UNO R3 AVR UNO:MicrocontrollerATmega328Operating Voltage5VInput Voltage (recommended)7-12VInput Voltage (limits)6-20VDigital I/O Pins14 (of which 6 provide PWM output)Analog Input Pins6DC Current per I/O Pin40 mADC Current..
Details
L293D Motor Drive Shield Kit For Arduino Duemilanove Mega UNO R3 AVR
UNO:
| Microcontroller | ATmega328 |
| Operating Voltage | 5V |
| Input Voltage (recommended) | 7-12V |
| Input Voltage (limits) | 6-20V |
| Digital I/O Pins | 14 (of which 6 provide PWM output) |
| Analog Input Pins | 6 |
| DC Current per I/O Pin | 40 mA |
| DC Current for 3.3V Pin | 50 mA |
| Flash Memory | 32 KB (ATmega328) of which 0.5 KB used by bootloader |
| SRAM | 2 KB (ATmega328) |
| EEPROM | 1 KB (ATmega328) |
| Clock Speed | 16 MHz |
Motor Driver Shield:
- L293D is a monolithic integrated, high voltage, high current, 4-channel driver.
- Basically this means using this chip you can use DC motors and power supplies of up to 36 Volts, thats some pretty big motors and the chip can supply a maximum current of 600mA per channel, the L293D chip is also whatrsquo;s known as a type of H-Bridge.
- The H-Bridge is typically an electrical circuit that enables a voltage to be applied across a load in either direction to an output, e.g. motor.
- 2 interface for 5V Servo connected to the Arduino's high-resolution dedicated timer - no jitter.
- Can drive 4 DC motors or 2 stepper motors or 2 Servo.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection.
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
- 4 H-Bridges: per bridge provides 0.6A (1.2A peak current) with thermal protection, can run motors on 4.5V to 36V DC.
- Pull down resistors keep motors disabled during power-up.
- reset button.
- 2 external terminal power interface, for seperate logic/motor supplies.
- Tested compatible for Arduino Mega, Diecimila amp; Duemilanove.
- Size:6.8cm x 5.5cm x 2cm - 2.68inch x 2.17inch x 0.79inch.
Prototype Shield:
It is a great kit to new Arduino users and geeks who have sparkling ideas. You can choose to do soldering in the soldering area. You can also make good use of the mini breadboard which can save your time of soldering, to try any circuit you want to the Arduino. You also can choose to use your own breadboard.
Arduino Protoytpe Shield:
- The small soldering area
- Access to a BlueSMiRF socket for wireless communication between Arduinos
- 2 general LEDs
- 1 general pushbutton switch
- 1 Arduino reset switch brought to top level
- 5V, GND, and Raw pins are exposed as well
- All Arduino pins are brought to the top level
Mini Breadboard:
- 170 tie points.
- Self-adhesive backing to stick on the Arduino Protoytpe Shield
- Strong
- Measures 1.7"x1.3"
Package List:
1x UNO
1x Motor Driver Shield
1x Protoytpe Shield
1x Mini Breadboard
65x Jumper Cable
1x USB Cable